BVS (Bildverarbeitungssystem): fault codes
All 64 fault codes of the Porsche Panamera (971, 2017–2023) BVS (Bildverarbeitungssystem) with the manufacturer's names. How to read and clear them with STEUER14.
| Code | Fault |
|---|---|
| B105000 | Function restriction, temperature above limit value |
| B11CE11 | Windshield heater for front sensor system, Short circuit to ground |
| B11CE15 | Windshield heater for front sensor system, Open circuit/short circuit to B+ |
| B163002 | Function restriction, route data not loaded |
| B1743F0 | Power steering control module, Sequence error during operating mode setting |
| B1872F0 | Control unit, internal supply voltage |
| B1948F0 | Internal data transfer, failed |
| B200005 | Ctrl. module faulty |
| B200009 | Ctrl. module faulty |
| B200044 | Control unit – function restriction |
| B2000F1 | Control unit – function restriction |
| B200500 | Coding |
| B200FF0 | Control unit – function restriction |
| B200FF1 | Control unit – function restriction |
| B200FF2 | Internal malfunction |
| B200FF3 | Internal malfunction |
| B200FF4 | Internal malfunction |
| B200FF5 | Internal malfunction |
| B200FF6 | Internal malfunction |
| B200FF7 | Internal malfunction |
| B200FF8 | Internal malfunction |
| B200FF9 | Control unit, faulty |
| B200FFA | Surround View camera - internal fault |
| B200FFB | Electromechanical power steering motor, Voltage too low |
| B200FFD | Internal malfunction |
| B201000 | Calibration |
| B201200 | Coding |
| B2F0B00 | Development code 11 |
| B2F0F00 | Development code 15 |
| C10A700 | Rolling test mode active |
| C10ACF2 | Steering, Interface for lane departure warning system not coded |
| C10ACF3 | Steering, Interface for lane departure warning system not available |
| C10ACF4 | Steering, Interface for congestion assistant not coded |
| C10ACF5 | Steering, Interface for congestion assistant not available |
| C110496 | Camera malfunction, Internal malfunction |
| C110500 | Vehicle Identification Number (VIN), Implausible |
| C1106F0 | Dynamic calibration, Limit value exceeded |
| C1106F1 | Dynamic calibration, Function limitation due to limit value exceedance |
| C110A46 | Camera control module, Calibration or parameter memory error |
| C110A76 | Camera control module, Incorrect installation location |
| C110AF0 | Camera control module, Restricted view |
| C110AF2 | Camera control module, limited visibility due to malfunction of optical path |
| C110AF3 | Camera control module, limited visibility due to malfunction of windshield inside |
| C110AF4 | Camera control module, limited visibility due to malfunction of windshield outside |
| C110AF5 | Camera control module, Camera height outside tolerance |
| C117554 | Matrix high beam left, No basic setting |
| C117654 | Matrix high beam right, No basic setting |
| C118E00 | Fog mode active |
| U041500 | Control unit for brake electronics (PSM) – signal implausible |
| U042900 | Steering wheel electronics control unit - signal implausible |
| U101100 | Supply voltage – too low |
| U101200 | Supply voltage – too high |
| U101400 | Coding |
| U103100 | FlexRay data bus, No synchronization |
| U110300 | Production mode active |
| U110400 | Expanded bus operation active |
| U112100 | Data bus - missing message |
| U112200 | Data bus - implausible message |
| U112300 | Data bus – fault value received |
| U140000 | Function restriction – supply voltage too low |
| U140100 | Function restriction – supply voltage too high |
| U140500 | Terminal 15 signal line – signal implausible |
| U150400 | CAN bus front light (AFS) – no communication |
| U150500 | Data bus front light, Faulty |
Fault names come from the manufacturer's diagnostic data. STEUER14 is independent and not affiliated with Porsche AG. A code tells you what a control unit detected, not always which part failed — check wiring, supply voltage and related codes before replacing parts. STEUER14 shows each fault's full description, status and freeze frame on the car.