Drive Motor Control Module: fault codes
All 134 fault codes of the Porsche 911 (992) Drive Motor Control Module with the manufacturer's names. How to read and clear them with STEUER14.
| Code | Fault |
|---|---|
| B107300 | Analog crash signal (PWM) - equipment fault |
| B12FD00 | Immobilizer |
| B184C00 | Release active |
| B18B0F0 | VKMS, Missing adaptation |
| B18B0F1 | VKMS, No basic data supply available |
| B18B0F2 | VKMS, Basic data supply inconsistent, new download container required |
| B18B0F3 | VKMS, Invalid key requirement detected during use |
| B2F0100 | Development code 1 |
| C116300 | Development functions active |
| P056000 | Terminal 30 power supply – signal implausible |
| P056200 | Supply voltage - voltage too low |
| P056300 | Supply voltage too high |
| P060200 | Programming |
| P060300 | Control unit - function restriction |
| P060400 | Control unit - function restriction |
| P060500 | Control unit - function restriction |
| P060600 | Control unit defective |
| P060700 | Ctrl. module faulty |
| P060A00 | Internal processor monitoring - malfunction |
| P060B00 | Control unit – internal error |
| P060C00 | Function restriction |
| P061A00 | Internal Control Module Torque Performance |
| P061B00 | Internal Control Module Torque Calculation, Performance |
| P062F00 | Function restriction |
| P063400 | Control unit - temperature switch-off |
| P064F00 | Coding |
| P0A0100 | Medium-temperature circuit – temperature implausible (TW5/TW9/TW10) |
| P0A1B00 | High-voltage power electronics faulty |
| P0A2B00 | Electric machine, temperature sensor – signal implausible |
| P0A2C00 | Electric machine, temperature sensor – short circuit to ground |
| P0A2D00 | Electric machine - temperature sensor – short circuit to B+/open circuit |
| P0A2E00 | Electric machine, temperature sensor – dropouts |
| P0A2F00 | Electric machine - temperature too high |
| P0A3C00 | Inverter - temperature too high |
| P0A4000 | Rotor position sensor - signal implausible |
| P0A4400 | Rotor position sensor - speed too high |
| P0A5200 | Electric machine current sensor - signal implausible |
| P0A5D00 | Electric machine - phase U - current implausible |
| P0A6000 | Electric machine - phase V - current implausible |
| P0A6300 | Electric machine - phase W - current implausible |
| P0A7800 | Inverter - no power output |
| P0A9300 | Inverter "A" Cooling System Performance |
| P0A9400 | Function limitation |
| P0AEE00 | Inverter, temperature sensor – signal implausible |
| P0AEF00 | Inverter, temperature sensor – short circuit to ground |
| P0AF000 | Inverter, temperature sensor – short circuit to B+ |
| P0AF300 | Inverter, temperature sensor 2 – signal implausible |
| P0AF400 | Inverter, temperature sensor 2 – short circuit to B+ |
| P0AF500 | Inverter, temperature sensor 2 – short circuit to B+ |
| P0AFA00 | High-voltage system - voltage too low |
| P0AFB00 | High-voltage system - voltage too high |
| P0BE600 | Electric machine, phase U current sensor – signal implausible |
| P0BE700 | Electric machine, phase current U sensor - short circuit to ground |
| P0BE800 | Electric machine, phase U current sensor - short circuit to B+ |
| P0BEA00 | Electric machine, phase V current sensor – signal implausible |
| P0BEB00 | Electric machine, phase current V sensor - short circuit to ground |
| P0BEC00 | Electric machine, phase current V sensor - short circuit to B+ |
| P0BEE00 | Electric machine, phase W current sensor - signal implausible |
| P0BEF00 | Electric machine, phase current W sensor - short circuit to ground |
| P0BF000 | Electric machine, phase current W sensor - short circuit to B+ |
| P0BFD00 | Electric machine, phase U-V-W sensors – signal implausible |
| P0C0100 | Electric machine - current too high |
| P0C0500 | Electric machine, phases U-V-W - open circuit |
| P0C1700 | Rotor position sensor - position not learned |
| P0C3A00 | Control unit – Function limitation |
| P0C3B00 | Control unit – Function limitation |
| P0C3F00 | Control unit – Function limitation |
| P0C4000 | Control unit – Function limitation |
| P0C4E00 | Rotor position sensor, number of calibration tests exceeded |
| P0C5000 | Rotor position sensor - electrical fault |
| P0CBD00 | Electric machine, coolant inlet temperature sensor – signal implausible |
| P0D2D00 | Electric machine, voltage sensor - electrical fault |
| P0D2E00 | Electric machine, current sensor – signal implausible |
| P0D2F00 | Electric motor - voltage sensor, short circuit to ground |
| P0D3000 | Electric machine, voltage sensor – short circuit to B+ |
| P0E3200 | Internal voltage sensor 1 – signal implausible |
| P0E3300 | Internal voltage sensor 2 – signal implausible |
| P0E3400 | Internal voltage sensor 2 – signal implausible |
| P0E3800 | Internal voltage sensor 2 – signal implausible |
| P0E3900 | Internal voltage sensor 2 – signal implausible |
| P0E5200 | DC/DC converter current sensor – signal implausible |
| P0E5300 | DC/DC converter current sensor - short circuit to ground |
| P0E5400 | DC/DC converter current sensor, short circuit to B+ |
| P0E9700 | High-voltage voltage converter, voltage sensor, below minimum |
| P0E9800 | High-voltage voltage converter, voltage sensor, below minimum |
| P0E9900 | High-voltage voltage converter, voltage sensor, below minimum |
| P151B00 | Engine electronics (DME) control unit – voltage at terminal 15 on ignition off |
| P160900 | Crash switch-off was triggered |
| P164000 | Function restriction |
| P164700 | Engine electronics (DME) control unit – coding defective |
| P253300 | Rear-end electronics, terminal 50 – short circuit to ground/open circuit |
| P262B00 | Control Module Power Off Timer Performance |
| P33D700 | High-voltage power electronics phase control - internal fault |
| U002800 | Hybrid CAN bus – faulty |
| U002900 | Hybrid CAN bus - no communication |
| U008000 | FlexRay data bus - synchronization |
| U010000 | Engine electronics (DME) control unit – no communication |
| U010100 | Lost Communication with TCM |
| U011200 | High-voltage battery control unit – no communication |
| U011600 | Thermal management control unit - missing message |
| U012100 | Brake electronics (PSM) control unit – no communication |
| U012A00 | Control unit for chassis control (PASM) – no communication |
| U014000 | Front-end electronics control unit (BCM1) - missing message |
| U014100 | Front-end electronics control unit (BCM1) - no communication |
| U014200 | Rear-end electronics control unit (BCM2) - missing message |
| U014600 | Gateway control unit - no communication |
| U015100 | Airbag control unit - missing message |
| U015500 | Instrument cluster control unit - missing message |
| U021200 | Steering wheel electronics control unit – missing messages |
| U030000 | Control unit, incorrect coding |
| U040100 | Engine electronics (DME) control unit – signal implausible |
| U040200 | Transmission control unit, signal implausible |
| U041300 | High-voltage battery control unit, signal implausible |
| U041500 | Control unit for brake electronics (PSM) – signal implausible |
| U041800 | Control unit for brake electronics (PSM) – signal implausible |
| U042200 | Front-end electronics control unit (BCM1) - signal implausible |
| U042900 | Steering wheel electronics control unit - signal implausible |
| U042B00 | Control unit for chassis control (PASM) – signal implausible |
| U043100 | Data bus - fault value received |
| U044300 | Data bus - fault value received |
| U044700 | Gateway control unit – signal implausible |
| U045200 | Airbag control unit - signal implausible |
| U045600 | Thermal management control unit - signal implausible |
| U059300 | High-voltage power electronics control unit, front axle - signal implausible |
| U104000 | Rear-differential lock control unit - signal implausible |
| U104100 | Rear-differential lock control unit - signal implausible |
| U106E00 | FlexRay data bus - signal error |
| U10E000 | Control unit for assistance systems – missing message |
| U110300 | Production mode active |
| U111100 | Operating and display log - missing message |
| U140000 | Function restriction – supply voltage too low |
| U140100 | Function restriction – supply voltage too high |
| U141B00 | Function restriction due to special software |
| U300100 | Control unit – run-on fault |
Fault names come from the manufacturer's diagnostic data. STEUER14 is independent and not affiliated with Porsche AG. A code tells you what a control unit detected, not always which part failed — check wiring, supply voltage and related codes before replacing parts. STEUER14 shows each fault's full description, status and freeze frame on the car.